a-52 apem www.apem.com a 55000 series vde approved toggle switches solder lugs straight pc terminals iii ii i 2-3 1-2 5-6 4-5 single pole double pole 55236a 55246a on - on 55239a 55249a on off on ?the switches described below are marked vde as standard. ?ul and csa agency approvals are also available. to order a switch marked ul or csa, please complete ?ther agency approvals" box. electrical specifications ?class i (normal insulation) ?small contact opening : (< 3 mm (.118)) ?current/voltage rating with resistive load : 3a 250vac - 6a 125vac ?dielectric strength : 2.000 vrms 50 hz min. between poles and between terminals and frame 1.000 vrms 50 hz min. between terminals ?special body for increased creepage distance and air gap : 3 mm (.118) materials ?contacts : silver ?case : diallylphthalate (dap) ?actuator : brass, chrome plated with insulating vinyl cap ?bushing : brass, nickel plated ?housing : stainless steel ?terminal seal : epoxy general specifications ?insulating cap, compulsory, supplied glued on the lever : u270 for models 55600a, 55200a and 55200za u1040 for models 55200wa and 55200wa x433 ?ground connector : u721 compulsory if the panel is not metallic or not connected to ground ?epoxy sealed terminals standard model structure also available with 6 mm (.236) bushing : 55500 . also available with 6 mm (.236") bushing : 55100 . iii ii i 2-3 1-2 5-6 4-5 single pole double pole 55636a 55646a on - on 55639a 55649a on off on further specifications, see 5000 series. ? keyway ? keyway (1/4-40uns) (.275) (.519) (.472) (.187) (.157 dia) (.070) (.314) (.452) (.472) (.145) (.039) (.078) (.185) epoxy 24? 1 3 6.35-40uns 1.80 7.00 4.70 4.00 4.75 13.20 12.00 2.00 8.00 11.50 1.00 12.00 3.70 (.433) 11.00 i ii iii 2 1.00 11.50 8.00 2.00 12.00 13.20 4.75 4.00 4.70 7.00 6.35-40uns 24? epoxy (.185) (.078) (.039) (.452) (.314) (.157 dia) (.187) (.472) (.519) (.275) (1/4-40uns) (.523) (.157) (.551) (.129) (.043) 4.00 13.30 14.00 3.30 1.10 (.185) (.187) (.185) (.062 dia) 1.60 4.75 4.70 4.70 11.00 (.433) iii ii i 1 2 3 en 61058-1
apem www.apem.com a-53 a 55000 series vde approved toggle switches right angle terminals - horizontal "x433" to be placed in the third box of ordering format. also available for vertical mounting (on request). p anel cut - out bushing 6,35 (1/4) bushing 6 (.236) levers -13 -4n for threaded bushing models cap u270 compulsory -13 for plain bushing models cap u1040 compulsory for use with paddles only iii ii i 2-3 1-2 5-6 4-5 single pole double pole* 55236wa 55246wa x433 on - on 55239wa 55249wa x433 on off on quick-connect terminals iii ii i 2-3 1-2 single pole 55236z on - on 55239za on off on * in double pole w models, spacing between poles on pcb is different from standard : 4,7 mm (.185) instead of 3,81 mm (.150) ? keyway (.500) (.185) (.291) (.500) (.291) 24? (.433) (.236) (.570) (.078) (.519) (.472) (.275) (.157 dia) (.185) (.246 dia) (.145) (.043) i (.500) (.185) (.500) (.185) (.185) (.200) (.200) (.062 dia) (.531) 7.00 6.25 4.70 12.00 3.70 4.00 5.08 5.08 4.70 1.10 12.70 7.40 14.50 6.00 11.00 2.00 4.70 12.70 7.40 12.70 12.70 4.70 13.20 4.70 1.60 13.50 3 epoxy ii iii 21 (1/4-40uns) (.275) (.519) (.157 dia) (.314) (.452) (.039) (.185) epoxy 24 i ii iii 6.35-40uns 7.00 4.70 4.00 13.20 8.00 11.50 1.00 12 3 (.061) (.515) (.208) 5.30 13.10 1.57 (.433) 11.00 5.20 2.20 6.50 (.086 dia) (.255 dia) (.204) (.086 dia) 2.20 6.20 6.20 (.244) (.244 dia) 1.00 9.00 (.039) (.354) (.452) 11.50 1.00 6.00 (.039) (.236) (.570) 14.50 12.00 (.472)
a-54 apem www.apem.com a 55000 series vde approved toggle switches other agency approvals to order a switch additionally marked ul and/or csa, complete above box with desired approvals. ul - csa + u... insulating caps and paddles ground connector u270 for threaded bushing models important : compulsory on models with threaded bushing if the panel is not metallic or not connected to ground. order separately. insulating caps compulsory - delivered assembled on the lever - n ot available in ivory colour u1040 for plain bushing models paddles for use with lever 4n only . shown with threaded bushing. order separately. u240n u721 u290n u390n cap/paddle colours replace last "0" by number 1 blue 1/4 dark blue 2 black 3 green 4 grey 5 yellow 7 ivory 7/1 white 9 orange (.433) 11.00 (.137 dia) 3.5 (.496) 12.60 (.259) (.208) (.088) 2.25 6.60 5.30 (.557) (.354) (1/4-40uns) 14.15 9.00 6.35-40uns (.787) 20.00 (.433) (.236) (.078) 2.00 11.00 6.00 (.848) (.354) 21.55 9.00 6.35-40uns (1/4-40uns) (.842) 21.40 (.433) (.551) (.708) (.236) (.078) 2.00 6.00 11.00 14.00 18.00 9.00 21.55 (.354) (.848) 6.35-40uns (1/4-40uns) (.188) (.031) (.255 dia) (.464 dia) (.291) (.055 dia) 6.50 11.8 1.40 4.80 7.40 0.80 (.531) 13.50 (.137 dia) 3.5 levers (continued) -33 for threaded bushing models -33 for plain bushing models 1.00 9.00 (.039) (.354) (.383) 9.75 4.40 (.173dia) 1.00 6.00 (.039) (.236) (.501) 12.75 (.173dia) 4.40
|